유조 (Fluid Bath)에서의 Pre-Angled 골내 치과용 임플란트의 피로 시험유조 (Fluid Bath)에서의 Pre-Angled 골내 치과용 임플란트의 피로 시험
Pre-angled 치과용 임플란트는, 치과 의사가 기존의 뼈를 최대한 사용하거나 뼈이식(bone grafting)을 할 필요성을 제거하기 위하는 것과 동시에, 치골에 안전한 회복 플랫홈을 제공하기 위하여 설계되었다.
피로시험에 대한 ISO 14801 기준의 최신 개정판에서는 실험실에서 이러한 pre-angled 치아 임플란트의 시험 방법에 대한 사양을 정의하여 줍니다. 본 기준에서 임플란트의 하중 각은, 임플란트 축과 연결 부위의 각이 주어진 축 사이의 각보다 10°더 크게 정열 되어야 한다고 요구합니다.
임플란트의 크기와 기하학적 배열을 통하여, angled 치아 임플란트는 ISO 14801 표준을 시험 하기 위한 다양한 각 고정구 (angle fixture)로 고정 될 수 있습니다. 고정구는 그 장착 방법에 의하여 임플란트를 과하게 구속 하지 않고, 로드셀이나 시험기기에 손상을 줄 수 있는 커다란 측면 방향 힘을 발생하지 않는다는 것을 보장해야 합니다. Pre-angled 치아 임플란트는 15Hz의 주파수를 사용하여, 상온 상태에서 시험되어야 합니다.
Straight 치아 임플란트와 마찬가지로, pre-angled 치아 임플란트 또한 부식 피로가 발생할 것이라 예측할 수 있다면, 유조 환경에서 시험될 수 있습니다. 고정구는 유조 (fluid bath)에서 장착되고, 식염수나 다른 생리적인 용액에 넣고 온도를37°C로 유지해줍니다.
우리의 E1000, E3000, 또는ElectroPlus™ linear motor test instruments는 치아 임플란트의 성능을 테스트 및 특성화하는데 이상적인 시험 기반을 제공합니다. 또는, 8870 series of servo-hydraulic fatigue testing systems이 사용될 수 있습니다. 치아 임플란트에 요구되는 토오크(torque)에 대한 연구를 행해야 할 필요가 있을 경우, 우리는 압축 및 비틀림 시험에 ElectroPlus E10000 Linear-Torsion test instrument나 우리의 8874 servo-hydraulic axial-torsion testing system을 사용할 것을 권장합니다.
우리는 이 기준을 복습함으로써 요구조건을 완전히 숙지할 것을 권합니다.
다른 치아 재료나 치아 임플란트에 대해 관심이 있으신가요? 인스트론은 치과 의학에 대한 다른 많은 시험장비를 갖고 있습니다.
Dental Implants ISO 14801
ISO 14801 “Dentistry – Implants – Dynamic fatigue test for endosseous dental implants” specifies the procedure for fatigue testing dental implants. Dental implants are designed by various manufacturers and are of different geometries and sizes depending on where they are placed within the mouth. ISO 14801 aims to establish a benchmark for in vitro testing of implants to compare different implant designs and geometries. It does not begin to replicate the complex conditions implants are subjected to when implanted within the oral cavity. Instron®’s latest design of the dental implant system is a turnkey solution to meet all of the requirements for ISO 14801 and is ideally suited for use with the ElectroPuls™ E1000 or E3000 test instruments.
- 제품소개
- 9/15/2017
- 1.0 MB
ElectroPuls E1000 시험기
ElectroPuls E1000 기계식 피로시험기는 광범위한 재료와 부품에 대한 동적(dynamic) 및 정적(static) 시험을 수행하기 위해 설계된 최신 기계식 피로 시험기입니다. +/- 1000N의 dynamic 하중 용량과 +/- 710N의 static 하중 용량을 지원하는 이 시험기는 시편 강성(stiffness)에 기반을 둔 손쉬운 튜닝이 가능하며, 전기적으로 작동하는 크로스헤드 리프트, 편리한 시험 set up을 위한 T-슬롯 테이블 등 최신 시험 기술이 포함되어 있습니다. 이 시험기는 추가적인 utility가 필요 없으며 편리하게 단상전원에 의해 구동됩니다.
- 제품소개
- 9/18/2006
- 0.5 MB
ElectroPuls E3000 시험기
ElectroPuls E3000 기계식 피로시험기는 광범위한 재료와 부품에 대한 동적(dynamic) 및 정적(static) 시험을 수행하기 위해 설계된 최신 기계식 피로 시험기입니다. +/- 3000N의 dynamic 하중 용량과 +/- 2100N의 static 하중 용량을 지원하는 이 시험기는 시편 강성(stiffness)에 기반을 둔 손쉬운 튜닝이 가능하며, 전기적으로 작동하는 크로스헤드 리프트, 편리한 시험 set up을 위한 T-슬롯 테이블 등 최신 시험 기술이 포함되어 있습니다. 이 시험기는 추가적인 utility가 필요 없으며 편리하게 단상전원에 의해 구동됩니다.
- 제품소개
- 9/18/2006
- 425.6 KB
ElectroPuls™ E3000 Linear-Torsion All-Electric Dynamic Test Instrument
The ElectroPulsTM E3000 Linear-Torsion is a state-of-the-art, all-electric test instrument designed for dynamic and static testing on a wide range of materials and components. It includes Instron® advanced digital control electronics, bi-axial DynacellTM load cell, Console software, and the very latest in testing technology – hassle-free tuning based on specimen stiffness, electrically operated crosshead lifts, a T-slot table for flexible test set ups and a host of other user-orientated features. Powered from a single-phase supply it requires no additional utilities for basic machine operation (for example, pneumatic air, hydraulics, or water).
- 제품소개
- 3/3/2017
- 0.7 MB
ElectroPuls E10000 All-Electric Dynamic Test Instrument
The ElectroPulsTM E10000 is a state-of-the-art, all-electric test instrument designed for dynamic and static testing on a wide range of materials and components. It includes Instron® advanced digital control electronics, DynacellTM load cell, Console software, and the very latest in testing technology – hassle-free tuning based on specimen stiffness, electrically operated crosshead lifts, a T-slot table for flexible test set ups and a host of other user-orientated features. Powered from a single-phase supply it requires no additional utilities for basic machine operation (for example, pneumatic air, hydraulics, or water).
- 제품소개
- 3/3/2017
- 0.7 MB
ElectroPuls™ E10000 Linear-Torsion All-Electric Dynamic Test Instrument
The ElectroPulsTM E10000 Linear-Torsion is a state-of-the-art, all-electric test instrument designed for dynamic and static testing on a wide range of materials and components. It includes Instron® advanced digital control electronics, bi-axial DynacellTM load cell, Console software, and the very latest in testing technology – hassle-free tuning based on specimen stiffness, electrically operated crosshead lifts, a T-slot table for flexible test set ups and a host of other user-orientated features. Powered from a single-phase supply it requires no additional utilities for basic machine operation (for example, pneumatic air, hydraulics, or water).
- 제품소개
- 3/7/2017
- 0.6 MB