당사 웹 사이트에서는 고객 맞춤 서비스를 제공하기 위해 쿠키를 사용합니다. 웹 사이트 탐색을 계속하면 쿠키 사용에 동의하시게 됩니다. 추가 정보

닫다 Close Cookie Notification
Instron
  • Back
  • Home
  • 제품
    시험기
    만능재료시험기
    구조물 내구성 시험기
    자동화 시험기
    레오미터 및 유동성 시험기
    동적 및 피로 시험기
    충돌 시뮬레이션
    비틀림 시험기
    낙하 충격시험기 / 펜듈럼 충격시험기
    HDT 및 VICAT
    생산 중단된 시스템
    액세서리
    소프트웨어
    로드셀
    박리, 마찰, 관통
    온도 챔버 및 고온로
    인장 그립
    굴곡 치구
    압축판
    바이오메디컬 치구
    신율계
    복합 비품
    전자분야 치구
    시편 측정 및 준비
    모든 액세서리
    액세서리 카탈로그
  • 산업 솔루션
    재료별 표준규격별 시험유형별
    산업별
    자동차
    바이오메디컬
    전자
    기재
    자동차
    바이오메디컬
    전자
  • 서비스 및 지원
    Instron Remote Technical Support 제품 수명 주기
    교육
    온라인 e-러닝
    서비스
    검교정
    Instron 운영지원
    기술 지원
    FAQs
    소프트웨어 업데이트 서비스
    자료
    매뉴얼
    시리얼번호
  • 회사소개
    채용 보도자료 뉴스레터 구독
    회사소개
    역사
    위치
    인증 및 성적서
    자료
    용어설명
    시험방법
    뉴스레터
    문헌 라이브러리
    뉴스
    이벤트
    Webinars
    사례연구
  • 연락처
  • 대한민국
제품소개 » 액세서리 » Flex Fixtures » Three-Point Bend Test Fixtures » Guided-Bend/Weld Bend Test Fixture

Guided-Bend/Weld Bend Test Fixture

General Purpose Flexure Fixtures

  • Guided Bend & Weld
  • Fixtures
Contact usView Accessories Catalog
W-6810
  • W-6810
  • 설명
  • Specifications

Two types of bend fixtures are available for evaluating the ductility of plate specimens and welded ferrous and non-ferrous materials. The main difference between the two fixtures is in the base, the guided bend test fixture has a fixed span base, while the weld bend test fixture has an adjustable span base.

Both fixtures use plungers or loading struts with a fixed diameter nose for testing a particular specimen thickness. The plungers are attached to the adjustable crosshead using the grip bumper plate or a threaded adapter. 

The base is equipped with a dowel hole in the center so that it can be doweled to the compression table and kept from sliding during a test. This also will maintain the alignment of the plunger in relation to base so that the force is applied in the center of the span. 

The hardened rollers in the base are captured but free to rotate to allow the specimen to slide as the plunger moves between the rollers. The depth of the base will typically allow up to a full 180 degree bend in the specimen.

Principle of Operation

The bending force is applied as the specimen is forced against the plunger, either as the base is raised with the table or as the crosshead moves down depending on the frame being used. The plunger forces the specimen into a 180 degree bend against the rollers on the base.

On the weld bend test fixture, one half of the base can be adjusted to one of four different positions to allow for testing different thickness specimens. A separate plunger or strut is required for each thickness specimen, several struts are available depending on the fixture.

Guided bend fixtures have a fixed span base and a single diameter loading strut or plunger to form a complete assembly. Specimen loading is carried the same as with the weld bend fixture though a separate assembly must be purchased for each specimen thickness.

Application Range

  • Type of Loading: compression bend 
  • Specimen Material: wrought or cast steel, non-ferrous materials 
  • Specimen Types: flat, flat welded

W-6810 | Guided-Bend/Weld Bend Test Fixture

Guided-Bend / Weld Bend Test Fixture, Adjustable Span for "U" bend tests of plane plate or welded flat specimens. 

Fixture consists of a t-slot base with adjustable span supports supported by two tie rods.

Fixture specifications:

  • Span - 0 to 254 mm (10.0 in)
  • Specimen width - up to 76 mm (3.0 in)
  • Support diameter - 38.1 mm (1.5 in) roller
  • Support depth - 135 mm (5.3 in)
  • Maximum Capacity - 100 kN (22,500 lbf)
  • Fixture Capacity

100kN (22,500 lbf) if installed fully supported

If installed with overhang, capacity is rated per below

Capacity = 100kN (22,500 lbf) where x < 125mm (5 in)

Capacity (kN) = 12,600/x when x > 125 mm

Capacity (lbf) = 111,900/x when x > 5 in

Where x = distance from end of machine loading table to lower flexure support

  • Lower connection - 12.7 mm (0.5 in) centering pin
  • Weight: 59 kg (130 lb) not including loading noses
  • Effective height with loading nose - 357 mm (14.06 in) not including specimen thickness.

Fixture meets the following US and International standards:

ASTM A370-07a, ASTM E190-92, ASTM E290-97a, ANSI/AWS B4.0-98, API 1104, API 5L, AS 2205.3.1, ASME IX 2004, JIS Z2248, GOST 14019 (for specimens 19 to 38.1 mm thick), ISO 5173, ISO 7438, EN ISO 15630-1, EN 910.

Notes:

  1. Fixture requires loading noses (sold separately) of appropriate size for material being tested and standard being used.
  2. The bend fixture cannot bend the specimen to a complete 180 degrees due to necessary clearances between the loading nose and supports.

W-6810-A | US Customary Loading Nose Set for Guided/Weld Bend Test Fixture

Includes 0.5, 1.0, 1.5, 2.0 inch diameter loading noses.

  • Loading nose width: 51 mm (2 in)
  • Loading nose height: 171 mm (6.75 in)
  • Attachment: Type R1m (1.0 in holding button)

CAUTION:
Most standards require loading nose diameters of 4 x specimen thickness. However, some standards allow for other diameter loading noses to be specified locally or as agreed between vendor and customer. It is the customer's responsibility to ensure the proper size loading noses are ordered.

Note: Other size loading noses available individually or in sets as special order.

W-6810-B | Loading Nose Set for Guided-Bend/Weld-Bend Test Fixture

Metric Loading Nose Set for Guided Bend / Weld Bend Test Fixture. Includes 12, 16, 20, 24, 32, 40, 48 mm diameter loading noses.

  • Loading nose width: 51 mm (2 in)
  • Loading nose length: 171 mm (6.75 in)
  • Attachment: Type R1m (1.0 in holding button)

CAUTION:
Most standards require loading nose diameters of 4 x specimen thickness. However, some standards allow for other diameter loading noses to be specified locally or as agreed between vendor and customer. It is the customer's responsibility to ensure the proper size loading noses are ordered.

Note: Other size loading noses available individually or in sets as special order.

Anvil Diameter 38.1 mm (1.5 in)
Capacity 100 kN (22,500 lbf)
Lower Fitting 12.7 mm (0.5 in)
Specimen Width up to 76 mm (up to 3.0 in)
Support Span 0-250 mm (0-10 in)
Upper Fitting Refer to W-6810-A/-B

Region Selector

Dismiss Region Selector

Americas

  • North America
  • Brasil
  • South America

All Other Countries

  • Global Site

Europe

  • France
  • Deutschland
  • Italia
  • Polska
  • España
  • Türkçe
  • United Kingdom

Asia Pacific

  • 中国
  • India
  • 日本
  • 대한민국
  • 台灣
  • ประเทศไทย
Instron Logo White
연락 정보

16FI, Hae-Am Building,
983-3 Daechi-dong,
Kangnam-gu, Seoul 135-842

영업문의 :  +82 2 552 2311

서비스 문의 :  +82-2-552-2315

유용한 링크
  • 시험기
  • 소프트웨어
  • 액세서리
  • 카탈로그
  • 용어 설명
  • 라이브러리
  • 시험 솔루션
  • 뉴스레터
  • Webinars
  • 사례 연구
  • 이벤트
  • 채용
Policies / Legal
  • 개인정보 보호 및 쿠키 정책
  • 사용약관
  • 수출제한법규
  • 개인정보보호(GDPR)
Instron 소셜미디어
뉴스레터 신청
이메일 주소
© Illinois Tool Works Inc. All rights reserved.
[email protected]
  • 개인정보 보호 및 쿠키 정책
  • 사용약관
  • 수출제한법규
  • 개인정보보호(GDPR)